The box includes only a Quick Setup Guide which is not sufficent for most of the TC users. I saw that there is no User Manual explaining technical datas like range, distance, capacity, frequency, pins etc. Solution: to disconnect and reconnect master NL solves the problem if the slave NL returned back inside the area. Same thing as you all started shooting inside of this area and the camera goes outside and returns to this area, same thing happens. If you have 1 camera and 1 recorder running both in Rec Run mode, if you start shooting inside this 23 meter range and you finish outside of the range, your recorder will continue recording even if the camera has been stopped. If the TC has been changed when you're outside of the range, you are unaware of what has been changed.Īs an example. The problem starts here: when you come back inside of the range, it is still using its TC Generator. You cannot observe anything on flashing leds saying that the mode has been changed. If the distance is more than 23 meters, the signal gets lost and NL switches automatically to TC Generator mode. Everytime that any of these 3 NL is lost, we start charging it and everything becomes normal. Finally we plugged the usb cable and suddenly they started working. We spent 1 hour and tried everything to reset these 2 NL in order to make them work again. We followed instructions in Quick Setup Guide to set all NL to TRX mode and we had a problem: 2 of them stopped responding, 1 was able to switch to TRX mode. We plugged it on a computer and reset its RTC then flashing led turned to red-green (normal) You have to understand what's the problem because there is no manual saying that it is because of RTC has been lost. If you don't have a computer on set and if your away from your recorder you can only use RTC and can not change FPS.Īt the second day of the test, one of NL's lost its RTC and started to flashing red light continuously when you turn it on. Fps also can be changed with an incoming TC signal. connect with cable to a device having target parameters. connect to a computer (no mobile phone or tablets)Ģ. There are two ways to change NL settings.ġ. TC drift was 0,5 frame between 3 NL during 24 hrs (working with 24fps). They were not responding incoming signals when the distance is more than that. Maximum distance that we measured was 23 mt. We were able to jam all 3 NL without any problem. Jamming with one button was so easy and quick. We tested ACN network range at outside of the city where there are nobody living near 6 kilometers. Leds shows us only if it is full or still charging. Unfortunately there is no way to see the actual amount of the battery. The device turns on automatically when you plug usb cable for charging. Here are our first impressions about them. We just got our brand new Nano Lockits and made a test on set. The ACN with C-Jam, auto framerate and autopower helps to eliminate these problems in the majority of applications. Doing support and troubleshhoting on timecode and sync here at Ambient since 1994 I know that most problems originate from untis not being kept on camera or not being powered on accidentially. I know, you guys here are savvy enough to deal with LockitToolbox and take care of TC well enough - Still, the Nano was designed above all to also help and guide the even most inexperienced and intimidated by the daunting timecode task. Have to power them down after charge is a trade off but cannot be avoided without risking they got shut off while on camera with external power and resulting TC inconsistencies. They come up with the camera and are ready to be synced, as soon you do, AC can do what they want - TC will always be there on spot. Many productions use them with external power and a C-Jam Master - they just stay on camera and do not need to be taken care of in any way, not even power on/down. However, we are evaluating an option so they can be configured to power down after external power has been disconnected." Very much like a mobile that’s on wouldn’t turn off after charging this is not going to change as they would otherwise shut down when powered externally while connected to camera. (or me, to be exact as it is a blunt copy and paste to my email answer the Nanos will come on automatically when connected and stay so in any condition.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |